SINKS

Sinks Are Part of the Countertop

A sink is the one part of a countertop that gets used every single day, and it is the detail people most often leave until last. That is a mistake, because the sink you choose determines how the stone around it has to be cut. The cutout, the support underneath, and the way the stone edge meets the basin all have to be planned before a slab goes on the saw.

We stock a wide selection of kitchen and vanity sinks, and we fabricate the countertop around whichever one you pick. Because we do both in the same shop, the cutout is measured against your actual slab rather than a drawing, and the reveal around the basin comes out even.

If you already have a sink you love, bring us the specifications and we will build the counter to fit it.

Kitchen and Vanity Sinks

We offer a large selection of sinks for kitchen and baths. If there’s something you don’t see but would like, please reach out to us and we’ll find it for you!

Choosing a Sink for a Stone Countertop

Stone changes the calculation compared with laminate or solid surface, in two ways worth understanding before you decide.

Support matters

An undermount or farmhouse sink hangs below the stone, so the weight of the basin plus the water in it has to be carried by the cabinet structure, never by the countertop. We build in the right support as part of the installation. A full farmhouse sink usually needs the cabinet modified, which is a conversation to have with your cabinet maker before anything is ordered.

The reveal is a design decision

With an undermount sink, the reveal is how much of the basin rim you can see through the stone cutout. A negative reveal hides the rim entirely behind the stone and looks cleanest. A positive reveal leaves a little of the rim visible and is easier to keep clean. A zero reveal lines the stone up flush with the basin edge, which looks sharp but leaves no margin for error. We will show you all three and recommend one for your slab.

Cutouts happen in the shop

Sink cutouts are made during fabrication, not on site. That is why we ask for your sink, or its exact template, before we cut. Changing the sink after a slab is cut generally means a new slab.

What to Look for in Stainless Steel

Gauge

Gauge measures thickness, and the number runs backward: a lower number means thicker steel. Sixteen gauge is thicker and more rigid than eighteen, which is in turn thicker than twenty-two. Thicker steel dents less easily and feels more solid under the hand.

Sound dampening

A thin sink drums when the tap hits it. Better sinks carry pads or a sprayed coating on the underside to deaden that noise. It is one of those details you never notice when it is done well and notice constantly when it is not.

Corner radius

Tight, near-square corners look modern and give you more usable basin space. Softly rounded corners are marginally easier to wipe out. This is purely a preference, and worth looking at in person.

Bowl configuration

A single large bowl handles baking sheets and roasting pans that will not fit in a divided sink. A double bowl lets you separate washing from draining. A low-divide sink splits the difference, with a partial divider that still allows long items to lie flat. How you actually cook should decide this, not how the sink looks empty.

Caring for a Stainless Sink

Stainless steel is easy to live with, but a few habits keep it looking new.

Everyday cleaning

Warm water, mild dish soap and a soft cloth. Wipe in the direction of the grain rather than in circles, and dry the basin afterward if you want to avoid water spots, which are mineral deposits rather than damage.

What to avoid

Steel wool and abrasive pads leave fine scratches and can embed particles that later rust. Bleach and cleaners containing chloride will pit the surface if left sitting. Do not leave cast iron or steel pans sitting wet in the basin overnight.

Around the stone

The joint between the sink and the countertop is sealed during installation. If you ever see water working its way under the edge of the stone, call us rather than waiting. It is a small fix early and a much bigger one later.

Common Questions

Do I need to buy the sink before you fabricate?

Yes, or at minimum give us the exact model and its template. The cutout is made in our shop against your specific sink, so we need it in hand or fully specified before a slab is cut.

Can I use my existing sink with a new countertop?

Often, yes. Bring us the sink or its specifications and we will build the cutout to match. The one thing to know is that an older drop-in sink will not always convert cleanly to an undermount installation.

Which sink style works best with granite or quartz?

Undermount is the most common choice with stone, because it shows off the cut edge and lets you wipe straight into the basin. Farmhouse looks superb but needs cabinet work. Drop-in is the most economical and the most forgiving.

Will an undermount sink pull away from the stone?

Not when it is supported correctly. The basin is carried by the cabinet structure rather than hanging from the countertop, and the joint is sealed during installation. Failures nearly always trace back to inadequate support underneath.

Can you cut a sink hole in a countertop I already have?

Sometimes, but it depends on the stone, the span and where the cutout falls. Cutting an installed countertop in place carries real risk of cracking. Come talk to us and we will give you an honest assessment before anyone touches it.

What is a workstation sink actually like to use?

It is a normal sink with a machined ledge running along the rim, so accessories slide across the basin. If your kitchen is short on counter space, it is genuinely useful. If you have plenty of counter, it is a nice extra rather than a necessity.

Ready to Choose Your Sink?

Schedule a free consultation and let's talk about your project.

Get Your Free Estimate